How to Attach Barb Wire to a Board for Art
This post contains affiliate links. If you buy through these links, I may earn a small committee.
Art made from used barbed wire is condign a Farmhouse decor favourite and I dearest the way it looks. Especially using erstwhile, rusty barbed wire! And since nosotros have some quondam rolls laying around, we figured out how to make a spinous wire Star to hang on the exterior wall down at the barn.
You lot tin use these tips to create your own custom metallic wall fine art.
How to Brand a Barbed Wire Star
The tools you will need include:
big lath, measuring tape, cord, pencil, 2 inch screws, drill, barbed wire, necktie wire, cutting pliers
Kickoff we had to make a template. Graham is way better at figuring out this kind of stuff, so I was glad he was so willing to help! Here'due south how he figured out the measurements.
Making a template for metallic art
Use any lath you have laying around for this projection. You but demand to make certain the board is large plenty for the size of star yous want.
You tin even reuse the lath after the farmhouse star is finished. The board will accept a few holes in information technology, though.
Measure the width of the lath and divide past ii. Make a mark at the heart betoken to work from in the next step. IF y'all have a big enough protractor for your circle, apply that instead of the following.
How to make a perfect circle using string
Using a drill, place a screw in the wood at the middle marker. Necktie a piece of string to the spiral and make a loop at the other end.
Put your pencil in that loop and pull the string tight. Keeping the string tight, draw a circumvolve on the forest.
Go all the way around until you have made a consummate circle. Now you tin can remove the string line and pencil.
Go your drill set. Grab some more screws. Information technology'south time to create the star.
The Spinous Wire Star Pattern
Figure out the equal distance between 5 screws in the circle. Hither'south how you can do that.
For example:
If the diameter of your circle is xx inches, multiply that past three.fourteen = 62.8
Now divide the 62.eight by 5 (the number of points on the star) = 12.5
There is 12.5 inches needed between each spiral.
At present anyone better than us at math probably has an easier way to effigy out the screw placement, but this is how we did it.
Leave the screws sticking out about i inch. You lot will need this tiptop for wrapping the spinous wire.
Wear leather gloves, you will be glad y'all did.
Wrapping the Barbed Wire
Selection any point to start and begin wrapping the barbed wire effectually the screw. For the first turn, leave a couple inches on the left side, wrap the wire around the screw and continue wrapping in a right handed direction.
You lot'll come back to stop off that lilliputian piece after.
At present only proceed wrapping the rusty barbed wire around the screws in a star shape. If y'all like, yous tin finish your star with just the 1 wrap around.
Or you can do 2 wraps, which gives you a bit chunkier of a star. You'll gear up upward those "loose" looking wires before you lot're washed.
We went with iii wraps of rusty barbed wire to brand the Metal Star even chunkier. To cut and secure the end, outset have a piece of wire ready.
Cut the length of excess barbed wire and wrap it a scrap effectually the other barbed wire to concord information technology in place. Wrap a piece of straight tie wire around all three runs of the barbed wire and cinch it using pliers. Expect at the photos, to encounter what I mean.
Now you tin can take brusque pieces of wire and work on whatever loose wires. We want to have the barb wire be tight and close together. Wrap the wire effectually the three pieces of wire at the intersections, where the cross wires meet.
If in that location are all the same any loose looking wires, just use some other piece of straight wire, line them up and cinch them together. Using pliers will make this role of the project much easier. Use the cut role of the pliers to cut the excess wire.
Once y'all are washed reinforcing the wires, y'all're set to lift the star from the board. Just use the drill to remove the screws from the board and the star tin just be picked up.
Hanging the Metal Star
You can use the straight wire to create a small hanger at the top of the star. If you want to keep the wait actually rustic, y'all're done. Hang 'er up. Information technology will look great against whatsoever kind of wood siding!
I decorated our star just a scrap. I used raffia to tie a simple bow, then added a sprig of red berries to give a little pop of color. The Barbed Wire Star is hanging alongside the Virginia Creeper that grows at our befouled.
I might add a few seasonal touches but maybe not. I similar the rustic simplicity of having the barbed wire be the focal point. Wouldn't a huge star hanging high up on our house gables wait great? That may be another project!
Experimenting with metal art using quondam rusty barbed wire has turned out to be a fun craft projection. You tin do so many things with it – maybe make a barbed wire cross or brand a farmhouse barbed wire wreath like this one.
More Farmhouse posts
How to Fix Up That Ugly Stairwell – You HAVE to see this "before" picture show; that stairwell was scary and super ugly!
Edifice Closets in the Loft – we needed more cupboard space and then we plow the loft off of our master bedroom into a spacious closet expanse.
How to Paint Over Ugly 1970's Wood Paneling – we had to. We merely had to. Nosotros brightened upward the entire house with this very unproblematic project!
Looking for the prettiest farmhouse porch decor? Bank check out our post!
Want to detect out which areThe 5 Easiest Vegetables to Abound?
Grab the free download available only to subscribers!
Source: https://countrylivinginacariboovalley.com/how-to-make-a-barbed-wire-star-farmhouse-decor/
0 Response to "How to Attach Barb Wire to a Board for Art"
Post a Comment